Anritsu Site Master S331D Bedienungsanleitung PDF herunterladen (Seite 61)

292) Status Byte 1: ( 0b = Off , 1b = On)

(LSB) bit 0 : Marker 1 On/Off

bit 1 : Marker 2 On/Off

bit 2 : Marker 3 On/Off

bit 3 : Marker 4 On/Off

bit 4 : Marker 5 On/Off

bit 5 : Marker 6 On/Off

bits 6-7: Not Used

293) Status Byte 2: ( 0b = Off , 1b = On)

(LSB) bit 0 : Not Used

bit 1 : Marker 2 Delta On/Off

bit 2 : Marker 3 Delta On/Off

bit 3 : Marker 4 Delta On/Off

bit 4 : Pre Amp Mode (0b = Manual, 1b = Auto)

bit 5 : Pre Amp Status On/Off

bit 6 : Dynamic Attenuation On/Off

bit 7: Reserved

294) Status Byte 3: (0b = Off, 1b = On)

(LSB) bit 0 : Antenna Factor Correction On/Off

bits 1-2 : Detection alg (00b = pos. peak 01b = RMS avg 10b = neg. peak 11b = sampling mode)

bits 3-4 : Amplitude Units (Log) - (00b = dBm 01b = dBV 10b = dBmV 11b = dBuV)

(Linear) – 00b = Watts 01b = Volts

bit 5 : Channel Power On/Off

bit 6 : Adjacent Channel Power On/Off

bit 7 : Units Type (0b = Log 1b = Linear)

295) Status Byte 4

170

(0b = Off/Beep if data is BELOW line, 1b = On/Beep if data is ABOVE line)

(LSB) bit 0 : Limit Type (0b = Single, 1b = Multiple)

bit 1 : Not Used

bit 2 : Single Limit On/Off

bit 3 : Single Limit Beep Level ABOVE/BELOW

bit 4 : Multiple Limit Upper Segment 1 Status On/Off

bit 5 : Multiple Limit Upper Segment 1 Beep Level ABOVE/BELOW

171

bit 6 : Multiple Limit Upper Segment 2 Status On/Off

bit 7 : Multiple Limit Upper Segment 2 Beep Level ABOVE/BELOW

296) Status Byte 5

( 0b = Off/Beep if data is below line, 1b = On/Beep if data is above line)

(LSB) bit 0 : Multiple Limit Upper Segment 3 Status On/Off

bit 1 : Multiple Limit Upper Segment 3 Beep Level ABOVE/BELOW

bit 2 : Multiple Limit Upper Segment 4 Status On/Off

bit 3 : Multiple Limit Upper Segment 4 Beep Level ABOVE/BELOW

bit 4 : Multiple Limit Upper Segment 5 Status On/Off

bit 5 : Multiple Limit Upper Segment 5 Beep Level ABOVE/BELOW

bit 6 : Multiple Limit Lower Segment 1 Status On/Off

bit 7 : Multiple Limit Lower Segment 1 Beep Level ABOVE/BELOW

172

297) Status Byte 6

(0b = Off/Beep if data is BELOW line, 1b = On/Beep if data is ABOVE line)

(LSB) bit 0 : Multiple Limit Lower Segment 2 Status On/Off

bit 1 : Multiple Limit Lower Segment 2 Beep Level ABOVE/BELOW

bit 2 : Multiple Limit Lower Segment 3 Status On/Off

bit 3 : Multiple Limit Lower Segment 3 Beep Level ABOVE/BELOW

bit 4 : Multiple Limit Lower Segment 4 Status On/Off

bit 5 : Multiple Limit Lower Segment 4 Beep Level ABOVE/BELOW

bit 6 : Multiple Limit Lower Segment 5 Status On/Off

bit 7 : Multiple Limit Lower Segment 5 Beep Level ABOVE/BELOW

298) Status Byte 7

(LSB) bits 0-6: Number of sweeps to average (1-25, 1 implies averaging OFF)

Site Master PM 55

170 For bits 2, 1 and 0 (“X” is “don’t care): 0X0=no limit, 1X0=single limit, 0X1=multiple limit, 1X1=multiple limit.

171 Upper limits always trigger an error beep if data is ABOVE the limit segment, for example, this bit is always 1b.

172 LOWER limits always trigger an error beep if data is BELOW the limit segment, for example, this bit is always 0b.

1 2 ... 56 57 58 59 60 61 62 63 64 65 66 ... 131 132

Kommentare zu diesen Handbüchern

Keine Kommentare

Anritsu Site Master S331D Bedienungsanleitung Seite 61

Kommentare zu diesen Handbüchern