Anritsu S331C Betriebsanweisung Seite 72
- Seite / 82
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
6-5 GPS Menu GPS (Option 31)
6-4 PN: 10580-00252 Rev. A Site Master User Guide
6-5 GPS Menu
Key Sequence: Shift, System (8) > GPS
GPS: Press this submenu key to turn GPS on or off.
GPS Info: Press this submenu key to display the current GPS information.
Tracked Satellites: Shows the number of tracked satellites (three are
required to retrieve latitude and longitude, four are required to resolve
altitude). Generally, the larger number of satellites tracked, the more
accurate the information.
Latitude and Longitude: Shows location in degrees, minutes, and
seconds.
Altitude: Shows altitude information in meters.
UTC: Universal Coordinated Time.
Fix Available: The cold start search sets are established to ensure
that at least three satellites are acquired within the first couple of
minutes. When three satellites are found, the receiver will compute an
initial fix (typically in less than two minutes). Fix Not Available means
that the initial position has not been established.
Almanac Complete: The system Almanac contains information
about the satellites in the constellation, ionospheric data, and special
system messages. In a cold start, the GPS receiver does not have any
navigation data so the receiver does not have a current almanac. A
complete system almanac is not required to achieve a first position fix.
The availability of the almanac, however, can significantly reduce the
time to first fix.
Antenna Status:
OK: Antenna is connected properly and antenna is working properly
Short/Open: A short or open exists between the antenna and the
connection. If this message is displayed, then remove and replace the
GPS antenna. If the message persists, then try another Anritsu GPS
antenna (part number 2000–1528-R). If the message persists, then
contact your nearest Anritsu Service Center.
Receiver Status: Current status of the receiver.
GPS Voltage: Press this submenu key to set the source voltage to be either
3.3 V or 5 V depending on the GPS receiver being used. GPS antenna
voltage is set to 3.3 V by default in order to prevent accidental damage to
lower-voltage GPS antennas.
Reset: The Reset key sets the tracked number of satellites to 0 and erases
any almanac data, along with saved coordinates. The process of searching
for and reacquiring satellites will begin again.
Back: Press this submenu key to return to the “System Menu” on page 5-3.
Figure 6-4. GPS Menu
GPS
Back
GPS
On Off
GPS Voltage
3.3 V 5 V
GPS Info
Reset
- Site Master 1
- S331E, S361E, S332E, S362E 1
- CE Conformity Marking 5
- C-tick Conformity Marking 5
- Notes On Export Management 5
- Mercury Notification 5
- Symbols Used in Manuals 7
- For Safety 8
- Table of Contents 9
- Table of Contents (Continued) 10
- 1-1 Introduction 13
- 1-2 Chapter Overview 13
- 1-3 Available Models 13
- 1-4 Available Options 14
- 1-5 Standard Accessories 14
- 1-7 Additional Documents 15
- 1-8 General Description 15
- 1-6 Optional Accessories 15
- 1-10 Preventive Maintenance 16
- 1-11 Calibration Requirements 16
- 1-12 Annual Verification 16
- 1-13 ESD Caution 17
- 1-14 Battery Replacement 17
- 1-15 Soft Carrying Case 19
- 1-16 Tilt Bail Stand 20
- Site Master Memory Types 21
- 2-1 Introduction 23
- 2-2 Chapter Overview 23
- 2-4 Front Panel Overview 24
- Front Panel Keys 25
- Touch Screen Keys 27
- Keypad Menu Keys (1 to 9) 27
- 2-5 Display Overview 28
- 2-7 Symbols and Indicators 32
- Additional Symbols 33
- 2-8 Data Entry 34
- 2-9 Mode Selector Menu 35
- 3-1 Introduction 37
- Select the Measurement Type 38
- Set the Frequency 38
- Set the Amplitude 38
- Turn on Markers 39
- Single Limit Line 40
- DTF Setup 41
- SiteMaster 42
- 3-4 Spectrum Analyzer 43
- Set the Span 44
- Segmented Limit Lines 45
- Create a Limit Envelope 46
- Setting Up Markers 47
- Chapter 4 — File Management 49
- Save Dialog Box 50
- Quick Name Keys 50
- Recall Files 51
- Recall Dialog Box 51
- Copying Files 52
- Deleting Files 53
- Delete Dialog Box 53
- 4-3 File Menu Overview 54
- 4-4 File Menu 55
- Save Menu 56
- Save Location Menu 56
- Save On Event Menu 57
- Recall Menu 58
- Copy Menu 59
- Delete Menu 60
- 5-1 Introduction 61
- 5-2 System Menu Overview 62
- 5-3 System Menu 63
- System Options Menu 64
- Reset Menu 65
- 5-4 Preset Menu 66
- 5-5 Self Test 67
- Chapter 6 — GPS (Option 31) 69
- Recalling GPS Information 71
- 6-5 GPS Menu 72
- 7-1 Overview 73
- 8-1 Introduction 75
- 8-2 MST Overview 75
- 8-3 Feature Overview 75
- 8-4 Installing MST 76
- A-1 Introduction 77
Verwandte Produkte und Handbücher für Messen, Testen & Steuern Anritsu S331C
(16 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern